Master Dell EMC D-RP-OE-A-24 Exam with Reliable Practice Questions

Correct : D

When a VPLEX distributed device is selected during the RecoverPoint Consistency Group Creation wizard, the option to create a MetroPoint Consistency Group becomes available. This is because MetroPoint is a feature that leverages VPLEX distributed devices for enhanced data protection and disaster recovery capabilities. The steps involved in this process typically include:

Selecting the VPLEX distributed device: During the creation of a Consistency Group, you choose the VPLEX distributed device as the source of replication.

MetroPoint option appears: Once a VPLEX distributed device is selected, the wizard presents the option to create a MetroPoint Consistency Group.

Configuring the MetroPoint Consistency Group: If you choose to create a MetroPoint Consistency Group, you will then configure the necessary settings, such as replication mode and RPO (Recovery Point Objective).

Finalizing the setup: After configuring the settings, you finalize the creation of the Consistency Group, which now has the enhanced capabilities provided by the MetroPoint feature1.

MetroPoint Consistency Groups are designed to provide continuous data protection and availability across multiple sites, combining the benefits of VPLEX Metro with the third-site replication provided by RecoverPoint1.

Correct : D

The priority level of a Consistency Group in Dell RecoverPoint is used to manage bandwidth allocation among multiple CGs that share the same primary RecoverPoint Appliance (RPA). Here's how it works:

Priority Level Setting: The priority level is set within the CG's settings, indicating its importance relative to other CGs.

Bandwidth Allocation: The higher the priority level, the more bandwidth is allocated to that CG when bandwidth is limited.

Resource Management: This setting helps ensure that critical CGs receive the necessary resources for replication, especially during peak times or when system resources are constrained.

Replication Efficiency: By managing bandwidth allocation through priority levels, RecoverPoint can maintain efficient replication and meet Recovery Point Objectives (RPOs) for all CGs1.

This feature is particularly important in environments with multiple CGs and limited bandwidth, as it allows administrators to ensure that the most critical data is replicated first1.

Correct : B

Calculate Daily Changes: With 100 GB of cumulative changes per day, the total amount of changes over two days would be 200 GB.

Determine Journal Size: The Journal size must be large enough to store all the changes for the required rollback periD. Therefore, a Journal size of 200 GB is necessary.

Set Protection Window: The ''Required Protection Window'' should be set for 2 days to match the rollback requirement.

Configure Copy Policy: The copy policy should be configured to ensure that the Journal maintains the point-in-time images for at least 48 hours.

By following these steps, the company can ensure maximum protection with the least amount of storage used, while also meeting their rollback requirements1234.

Correct : A

In Dell EMC RecoverPoint, virtual RPAs (vRPAs) use iSCSI protocol for connections. This is because vRPAs are designed to operate in virtual environments where iSCSI is commonly used for storage networking due to its ability to work over standard IP networks. Physical RPAs, such as Gen-5 and Gen-6, typically use Fibre Channel (FC) for direct storage connectivity1.

Here's a breakdown of the connectivity:

vRPA: Utilizes iSCSI for connections to protected storage. This is suitable for virtualized environments where the RecoverPoint for Virtual Machines (RP4VMs) operates.

Gen-5 and Gen-6 RPAs: These are physical appliances that generally use Fibre Channel for connectivity, which is more common in physical data center environments where dedicated storage networks are present1.

It's important to choose the correct RPA type based on the storage infrastructure and connectivity requirements of the environment1.

Correct : D

When using RecoverPoint Unisphere to collect system information, the ''Collect System Information'' file can be stored on an FTP server that is configured on the RPA cluster. This allows for centralized storage and easy access to the file for further analysis or troubleshooting. The steps typically involve:

Accessing Unisphere: Log into the RecoverPoint Unisphere interface.

Running the Wizard: Navigate to the appropriate section and run the ''Collect System Information'' wizard.

Choosing Storage Option: Select the option to store the file on an FTP server configured on the RPA cluster.

Retrieving the File: Access the FTP server to retrieve the ''Collect System Information'' file as needed.

This method ensures that the collected system information is securely stored and can be accessed by authorized personnel for maintenance or support purposes1.