Master CWNP CWNA-109 Exam with Reliable Practice Questions

Correct : C

A VoIP phone is least likely to be a POE PSE of the devices listed. POE stands for Power over Ethernet, which is a technology that allows devices to receive both power and data over a single Ethernet cable. A POE PSE stands for Power Sourcing Equipment, which is a device that provides power to other devices over Ethernet. A POE PD stands for Powered Device, which is a device that receives power from a PSE over Ethernet. A midspan multi-port injector, a switch, and a midspan injector are examples of POE PSEs, as they can supply power to multiple devices over Ethernet cables. A VoIP phone is an example of a POE PD, as it can receive power from a PSE over an Ethernet cable.However, some VoIP phones can also act as POE PSEs for other devices, such as IP cameras or wireless access points, but this is not very common.Reference:CWNA-109 Study Guide, Chapter 8: Wireless LAN Access Points, page 2411

Correct : C

A POE device that requires 47 W of power should use the 802.3bt specification. This is because 802.3bt is the latest POE standard that supports up to 90 W of power delivery over four pairs of wires in an Ethernet cable. The previous POE standards, such as 802.3af and 802.3at, only support up to 15.4 W and 30 W of power delivery over two pairs of wires in an Ethernet cable, respectively. Therefore, they are not sufficient for powering a device that requires 47 W of power.The 802.11at specification does not exist; it is a typo or confusion with the 802.3at specification.Reference:CWNA-109 Study Guide, Chapter 8: Wireless LAN Access Points, page 2431

Correct : A

The statement that in modern networks, both centralized and distributed data forwarding work well for most standard office deployments is true about WLAN performance. Data forwarding refers to how wireless frames are transmitted from wireless clients to wired networks or vice versa through wireless access points (APs). Centralized data forwarding means that all wireless frames are sent to a central controller or gateway before being forwarded to their destinations. Distributed data forwarding means that wireless frames are forwarded directly by the APs to their destinations without going through a central controller or gateway. Both methods have their advantages and disadvantages, depending on the network size, topology, traffic pattern, security, and management requirements. However, in modern networks, both methods can achieve high performance and scalability for most standard office deployments, as they can leverage advanced features such as fast roaming, load balancing, quality of service, and encryption. The other statements about WLAN performance are false. In most WLANs, special skill or tuning is required to get peak performance, such as selecting the appropriate channel, power, data rate, and antenna settings. WLANs perform worse as more wireless clients connect with each AP, as they cause more contention and interference on the wireless medium.To get the best performance out of an AP, you should not disable data rates of 72 Mbps and lower, as they are needed for backward compatibility and range extension.Reference:CWNA-109 Study Guide, Chapter 9: Wireless LAN Architecture, page 2811

Correct : B

An access point is configured by a WLAN controller in the management plane of the three networking planes. The management plane is responsible for the configuration, administration, and monitoring of network devices, such as access points, switches, routers, and controllers. The WLAN controller communicates with the access point using a management protocol, such as CAPWAP or SNMP, to send configuration commands and receive status information. The control plane is responsible for the routing, switching, and forwarding of network traffic, such as data frames and control frames. The WLAN controller may also participate in the control plane by performing functions such as authentication, encryption, roaming, and load balancing. The security plane is responsible for the protection of network devices and data from unauthorized access, modification, or disclosure. The WLAN controller may also participate in the security plane by implementing features such as firewall, VPN, IDS/IPS, and WIPS. The data plane is responsible for the transmission and reception of user data, such as voice, video, or web traffic. The WLAN controller may or may not participate in the data plane depending on the architecture of the WLAN. In some cases, the access point forwards the user data directly to the wired network without involving the WLAN controller (distributed data forwarding). In other cases, the access point tunnels the user data to the WLAN controller before forwarding it to the wired network (centralized data forwarding).Reference:CWNA-109 Study Guide, Chapter 9: Wireless LAN Architecture, page 279

Correct : B

A 5 GHz channel should be used for this AP because channels 1 and 6 are 2.4 GHz channels and they have no impact on the decision. The 5 GHz frequency band offers more non-overlapping channels than the 2.4 GHz frequency band, which reduces interference and improves performance. The 5 GHz frequency band also supports higher data rates and wider channel bandwidths than the 2.4 GHz frequency band, which increases capacity and throughput. The 5 GHz frequency band also has less interference from other devices and sources than the 2.4 GHz frequency band, which enhances reliability and quality of service. Therefore, it is recommended to use the 5 GHz frequency band for WLANs whenever possible. Channels 1 and 6 are two of the three non-overlapping channels in the 2.4 GHz frequency band (the other one is channel 11). They are used by a neighbor network in this scenario, but they do not affect the channel selection for this AP because they operate in a different frequency band than the 5 GHz frequency band. Channel 6 is not always best to use; it depends on the interference and congestion level in the environment. Channel 1 is not best to use because it has a lower frequency than channel 6; frequency does not determine channel quality or performance. Channel 11 is not best to use because it is also a 2.4 GHz channel and it may interfere with channels 1 and 6.Reference:CWNA-109 Study Guide, Chapter 4: Antenna Systems and Radio Frequency (RF) Components, page 113