Master CWNP CWAP-404 Exam with Reliable Practice Questions

Correct : B

It is possible to distinguish between OFDM 20 MHz transmissions and HT 20 MHz transmissions when looking at an FFT plot. OFDM and HT are two different modulation schemes used by 802.11 WLANs. OFDM is used by legacy 802.11a/g devices, while HT is used by newer 802.11n/ac devices. OFDM and HT have different spectral characteristics that can be observed on an FFT plot. OFDM transmissions have a flat spectrum with sharp edges, while HT transmissions have a tapered spectrum with rounded edges. This is because HT uses guard intervals and cyclic prefixes to reduce inter-symbol interference and improve performance. The other options are not correct, as they do not describe different modulation schemes or channel widths that can be distinguished on an FFT plot.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 70-71

Correct : D

The function of the PHY layer is to convert PSDUs to PPDUs for transmissions and PPDUs to PSDUs for receptions. A PSDU (PHY Service Data Unit) is the data unit that is passed from the MAC layer to the PHY layer for transmission, or from the PHY layer to the MAC layer for reception. A PPDU (PHY Protocol Data Unit) is the data unit that is transmitted or received over the wireless medium by the PHY layer. A PPDU consists of a PSDU and a PHY header, which contains information such as modulation, coding, and data rate. The PHY layer adds or removes the PHY header to or from the PSDU during the conversion process.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

Correct : D

The function of the PHY preamble is to allow the receiver to detect and synchronize with the signal. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to adjust its parameters, such as frequency, timing, and gain, to match the incoming signal. The PHY preamble also helps the receiver to estimate the channel conditions and noise level.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

Correct : C

The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

Correct : C

A STA that supports 802.11k Radio Measurement would send a Neighbor Request to an AP to request a list of neighboring APs which the STA can use as roaming candidates. A Neighbor Request is an Action frame that contains a subelement specifying the type of information that the STA wants to receive from the AP. A Neighbor Report is an Action frame that contains a subelement with a list of neighboring APs that match the criteria specified in the Neighbor Request. The Neighbor Report provides information such as BSSID, channel, operating class, and PHY type of each neighboring AP. This information helps the STA to perform intelligent roaming decisions based on signal quality, load, and compatibility . Reference: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 435.